Installed Voice Business Group RS-232 Command Set: Vortex EF2211 Programming Guide Copyright © 2003 Polycom, Inc. Polycom and the Polycom lo
chosen as the terminator to allow manually typing commands using a simple text terminal. 4.6. ExamplesIn the following examples, Vortex commands are e
S01PEQIF1,2,1250Set frequency of parametric EQ on input 1 , band 2 to 1250 Hz. S01PEQIF1,2,1250S01PEQIFB,1,?Query current frequency setting of paramet
(EQ) filters on input channels 1, A, B, and T . Each channel has five bands of parametric EQ that can be independently controlled. For the Linkwitz-Ri
parameter, the filter type, is specified instead of all the parameters. See the PEQIA command for more information. To set the slope parameter for an
Gain -20 - 20 dBSlope1 - 1.2 * Gain for shelving filters, 12 or 24 for Linkwitz-Riley filtersdB per octaveEnable 0 - 10 = filter disabled1 = filter en
S01PEQOA1,2,1,1250,40,-20,1,1Set the parametric EQ on output 1 , band 2 to the following parameters: type = parametric filter, frequency = 1250 Hz, ba
preset. Example Description Status MessageS01PEQOB1,2,40Set bandwidth of parametric EQ on output 1 , band 2 to 40 1/100th octaves. S01PEQOB1,2,40S01PE
This command sets or queries the frequency parameter (in Hz) for the parametric equalizer (EQ) filters on output channels 1, A, B, and T . Each channe
This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is s
S01PEQOSB,1,?Query current slope setting of parametric EQ on output B , band 1. S01PEQOSB,1,s , where s is the current setting of the slope parameter
S01PEQOT1,2,1Query current type setting of parametric EQ on output B , band 1. S01PEQOTB,1,t , where t is the current setting of the type parameter fo
6.1. Boolean CommandsBoolean commands take one of the three following arguments. ● '0' indicates that the parameter should be turned off
S01PHONE2Toggle hook status of phone interface. If the phone was off-hook, then this command puts it on-hook. If the phone was on-hook, then this comm
Example Description Status MessageS01PRESETK18Delete preset number 18. S01PRESETK18S01PRESETK*Delete all presets. S01PRESETK*8.132. PRESETL -- List Al
This command executes the preset corresponding to the specified number, which must be between 0 and 47. The preset must either be a pre-defined factor
Example Description Status MessageS01PRESETX18Execute preset number 18. Status messages for all the commands in the preset will be generated first, fo
This command sets the effective output gain of the corresponding AEC reference. When doing volume control of room speakers, it is a good idea to adjus
S01RING1Enable auto answer mode.S01RING1S01RING0Disable auto answer mode.S01RING0S01RING2Toggle auto answer mode.S01RINGx , where x is 0 or 1 dependin
S01SGMUTE2Toggle mute on signal generator.S01SGMUTEx , where x is 0 or 1 depending on the current state of the signal generator mute. S01SGMUTE?Query
6 quick double buzz7 long single buzzThe SOUNDL and SOUNDP were originally implemented to allow users to implement custom passcode systems that requir
This command sets or queries the amount of time (in milliseconds) between each new screen of the LCD screen saver. This command is an integer command.
This command sets or queries the amount of time (in milliseconds) that the front panel buttons must be idle before the screen saver starts. This comma
respond with a status message of ' S04AGC10 '. An example of an integer channel command is the 'GAINI' command, which adjusts the
S01SSTEXT0,1,?Query the text of the second line of the first screen. S01SSTEXT0,1,<string> , where <string> is the text of the second line
S01TONEE2Toggle enabled status of entry and exit tones.S01TONEEx , where x is 0 or 1 depending on the current enabled state of entry and exit tones. S
S01VTXMODIB0Disable VTX mode on input B. S01VTXMODIB0S01VTXMODIB2Toggle status VTX mode on input B. S01VTXMODIBx , where x is either 0 or 1 depending
S01VTXMODOA?Query status of VTX mode on output A. S01VTXMODOAx , where x is either 0 or 1 depending on the current status of VTX mode on output A. S01
Queries using the '?' character are straightforward. For example, ' S04GAINI1? ' might return ' S04GAINI110 ', while &ap
tied to output 1. Thus the signal routed to output 1 will also be routed to the power amplifier output. This yields a total of four physical outputs.
● Inputs: WB0-WB7 (with one invalid)● Outputs: WM0-WM2X Submatrix● Inputs: XB0-XB7 (with one invalid)● Outputs: XM0-XM2Y Submatrix●
It is also possible to use the wildcard character ('*') to specify ranges of crosspoints with the matrix commands. The only restriction is t
The Storage column contains one of the following values indicating when and where the parameter is stored. ● "Global"● "Preset&
AMNOMPreset Set Local Maximum Number of Open Mics for AutomixerAMNOMATPreset Select NOM Attenuation on Each OutputAMOFFATPreset Set Off Attenuation fo
GAINIPreset Set Input GainGAINOPreset Set Output GainGAINPPreset Set Phone Output GainGAINSITPreset Set From Phone User Tone GainGAINSOTPreset Set To
Vortex EF2211 Programming GuideTable of Contents1. Introduction2. RS-232 Hardware3. Programming Tips3.1. Initialization3.2. Wildcard Characters3.3. Us
MACROA- Add Command to Current MacroMACROKGlobal Delete One or All MacrosMACROL- List All Commmands in a MacroMACROQ- Execute Macro QuietlyMACROS- Sta
PEQOSPreset Set Slope Parameter for Specified Parametric EQ Output StagePEQOTPreset Set Type Parameter for Specified Parametric EQ Output StagePHANTOM
This command sets or queries the status of the auto answer feature. This command is a boolean command. See Section 6.1 for more information on this ty
This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is s
channels 1 and T (the telephone input) . Using the wildcard character, '*', to specify the channel with this command is not supported for th
S01AGCMAXT?Query the AGC maximum gain on input channel T . S01AGCMAXTx where x is a number between 0 and 15, depending on the current setting of the A
This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is s
off-hook or busy tones and hangs up the phone if they are detected. The loop drop method looks for a drop in loop current on the phone line and hangs
8.12. AMAUTO -- Select Automatic or Manual Gating for each Automixer InputThis command selects or queries the state of automatic or manual automixer g
This command is a channel integer command. See Section 6.3 and Section 6.2 for more information on this type of command. The minimum and maximum value
8.14. AMCHAIR -- Enable Chairman Mode for Specified Automixer8.15. AMCHNUM -- Set Chairman Mic8.16. AMDECAY -- Set Decay Time for Automixers8.17. AMGA
8.15. AMCHNUM -- Set Chairman MicThis command sets the chairman microphone for the automixer. The first argument of the command specifies the automixe
S01AMDECAY>500Increase automixer decay time by 500 ms. S01AMDECAYx , where x is between 0 and 5000 depending on the current AMDECAY setting. If thi
This command is a channel integer command. See Section 6.3 and Section 6.2 for more information on this type of command. The minimum and maximum value
S01AMGATET1>3Increase gate threshold for manual gating threshold by 3 dB for input channel 1. S01AMGATET1x , where x is between 0 and 100 depending
This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are
S01AMLMM10Disable "last mic on" mode for automixer 1. S01AMLMM10S01AMLMM11Set "last mic on" mode to manual for automixer 1. S01AML
for AutomixerThis command sets the local maximum number of open mics (NOM) allowed for the specified automixer. The NOM limit is a local limit, meanin
S01AMNOMAT11Enable NOM attenuation on output 1 . S01AMNOMAT11S01AMNOMATA0Disable NOM attenuation on output A. S01AMNOMATA0S01AMNOMATT2Toggle NOM atten
This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is s
Even though this is a channel integer command, use of the wildcard character for the automixer number is not supported. This command is a channel inte
8.59. GAINO -- Set Output Gain8.60. GAINP -- Set Phone Output Gain8.61. GAINSIT -- Set From Phone User Tone Gain8.62. GAINSOT -- Set To Phone User Ton
S01AMREFE11Enable automixer reference mode for Automixer 1. S01AMREFE11S01AMREFE1?Query current setting of automixer reference mode for Automixer 1. S
S01BLAUTO?Query enabled status of automatic BLDATA messages. S01BLAUTOx , where x is 0 or 1 depending on the current setting of BLAUTO. 8.32. BLDATA -
translate to AEC states. Byte Value AEC State Value (Byte Value - 132) AEC State Description132 0 Idle133 1 Transmit134 2 Receive135 3 Double TalkHere
The last byte (ä) consists of only one value. ä = 0x84 = 132 → 132 - 132 = 0 = Idle So, we know that the AEC on input 1 is in idle mode. In the above
Voice Business Group in Atlanta. Example Description Status MessageS01BROAD2:ATDT4048921180Sends the string ATDT4048921180 out the RS-232 port.S01BROA
Example Description Status Message Put AEC Reference 1 (R1) on the EF Bus. Set Vortex to not place any AEC reference on the EF Bus. S01BUSREF?Quer
This command is saved to non-volatile memory only as part of a preset. The state of this command will be restored after power-up only if a preset is s
8.40. COUNTRY -- Specify Country Definitions for Phone InterfaceThis command is used to set or query the country that the Vortex is configured for ope
S01DELAYOB1500Set output delay on output channel B to 150 ms (1500 tenths of milliseconds). S01DELAYOB1500S01DELAYOB>1700Increase output delay on o
S01DELAYOE*0110Enable output delay on outputs A and B, and disable output delay on outputs 1 and T. S01DELAYOE*0110S01DELAYOE*2Toggle enabled status o
8.104. MINISTR -- Set Modem Initialization String8.105. MMUTE -- Mute Crosspoint in Main Matrix or Submatrix8.106. MUTEGIL -- Set Mute Status of Line
S01DSPAUTO?Query the value of the DSPAUTO parameter.S01DSPAUTOx , where x is 0 or 1 depending on the current setting of the DSPAUTO paramter. 8.45. DS
ERROR#043This error occurs as the result of an AMLMN command. It happens when the command attempts to set a "last mic on" number that does n
ERROR#092This error indicates an EF Bus ID conflict. See the Vortex user manual for information on valid device IDs. ERROR#093This error indicates an
S01FADERGIL>3Increase fader gains on all line inputs by 3 dB. S01FADERIAaS01FADERIBb,where a and b are the new values of the fader gains for each o
S01FADERIA?Query the fader gain on input A. S01FADERIAx , where x is a number between 0 and 30, depending on the current setting of the fader gain on
We recommend using hardware flow control whenever possible, especially when using higher baud rates. This command is saved to global non-volatile memo
8.52. FPPSWD -- Change Front Panel PasswordThis command sets or queries the front panel password. This password is used in conjunction with the FPLOCK
This command is an integer command. See Section 6.2 for more information on this type of command. The minimum and maximum values for this command are
This command sets the gain of the dial tone received from the phone interface. This command is an integer command. See Section 6.2 for more informatio
S01GAINGIL>3Increase incoming gain on all line inputs by 3 dB. S01GAINIAaS01GAINIBb ,where a and b are the new values of each of the line inputs. I
8.149. SSTEXT -- Set Text to be Displayed by Screen Saver8.150. SWRESET -- Perform Soft Reset of System8.151. SWVER -- Query Software Version8.152. TO
Example Description Status MessageS01GAINIA10Set gain on input A to 10 dB. S01GAINIA10S01GAINIA?Query the gain on input A. F01GAINI2xB01GAINITxS01GAIN
S01GAINO*äììäSet gain on output channels 1 and T to 0 dB, and gain on output channels A and B to 9 dB. S01GAINO*äììäS01GAINO*?Query gain settings on a
will be restored after power-up only if a preset is saved and that preset is set to be the power-on preset. Example Description Status MessageS01GAINS
status of all the microphone inputs. On the EF2211 and EF2210, there is only one microphone, so the wildcard character is of limited use. The GATEEN c
The name of this command is an abbreviation of "Global Mute Outputs." Enabling this option causes all of the physical outputs to be muted (o
iLABELx,y where i is the device type and ID, x is the label specifier, and y is the label text (to set the label) or a ? character (to query the label
This command was introduced in firmware version 2.5.0. This command is a channel boolean command. See Section 6.3 and Section 6.1 for more information
preset. Example Description Status MessageS01LAGCLINKAB1Enable stereo AGC linking on inputs A and B. S01LAGCLINKAB1S01LAGCLINKAB0Disable stereo AGC li
LAGCMIN is set to -10, then the AGC for that channel can apply a minimum of -10 dB of gain to the input signal. This command was introduced in firmwar
This command sets or queries the status of the line echo canceller (LEC). This command is a boolean command. See Section 6.1 for more information on t
3.2. Wildcard CharactersThe use of the wildcard character, '*', can make programming the host controller much easier. Be careful when using
24 boolean values is returned with the first value indicating the state of the first logic input, the second value indicating the state of the second
S01LIA4,MUTEI11Assign the command MUTEI11 to occur when logic input pin 4 changes from the inactive to active state. The MUTEI11 mutes input channel 1
This function assigns a single command to be executed when a given logic input changes from the active state to the inactive state. Typically, the ina
MACROQ command. Since up to 256 commands can be stored in each macro, this gives the effect of having up to 256 commands execute when the logic pin ch
Example Description Status MessageS01LIEN1Enable automatic logic input status messages.S01LIEN1S01LIEN0Disable automatic logic input status messages.S
8.81. LIK -- Delete One or All Logic Input Pin CommandsThis command "kills" or deletes all commands for a given logic input pin. In other wo
S01LIM100101101111011111111111Mask (disable) logic inputs 2, 3, 5, 8, and 13. S01LIM100101101111011111111111S01LIM?Query current logic input mask. S01
closed switch would ground the input, and a closed switch would normally be considered active. This command affects the operation of the LIA, LID, and
StateThis command is used to define the conditions under which a given logic output pin goes into the active state. By default the logic output pins a
S01LOA10,MUTEI*1+-.Configure the conditions for activation of logic output 10 as described in the example above. S01LOA10,MUTEI*1+-.S01LOA7,Delete con
3.4. Macros and PresetsAlthough macros and presets are similar, there are times when using one is better than the other. Presets store the absolute va
S01LOEN?Query automatic logic output status messages.S01LOENx , where x is 0 or 1 depending on the current setting of LOEN. 8.89. LOK -- Delete One or
Example Description Status MessageS01LOM10010110111101111111Mask (disable) logic outputs 2, 3, 5, 8, and 13. S01LOM10010110111101111111S01LOM?Query cu
● any PRESET command● any MACRO command● any logic input or output commandIf an attempt to assign an invalid command to a macro is made (v
S01MACROK*Delete all the commands associated with all 255 macros. S01MACROK*8.94. MACROL -- List All Commmands in a MacroThis command lists all the co
This command is used to start writing a new macro with a specified macro number. This command is used in conjunction with the MACROA and MACROW comman
This command selects which signal is displayed on the front panel LED meter. The options correspond to either the telepone input or telephone output.
S01MGAINWB0,WM0,-3Set crosspoint gain in EF Bus submatrix on crosspoint that routes the W bus signal from the device at ID0 (WB0) to W submatrix outpu
This command is a matrix boolean command. See Section 6.4 and Section 6.1 for more information on this type of command. This command is saved to non-v
S01MIC1?Query enabled status of microphone gain stage for input channel 1. S01MIC1x , where x is 0 or 1 depending on the current enabled state of the
Example Description Status MessageS01MINISTRATF1E0&B1S0=2Set modem initialization string to ATF1E0&B1S0=2. S01MINISTRATF1E0&B1S0=2S01MINIS
A single alphanumeric character is used to indicate the device type. The devices in Polycom's EchoFree family have the following device types. De
S01MMUTE1,*,0110100000Set all crosspoint mutes for input channel 1. Mute the paths from input 1 to outputs A, B, and P and unmute the paths from input
S01MUTEGIL2Toggle mute status of all line inputs. S01MUTEIAaS01MUTEIBb ,where a and b reflect the mute status (0 or 1) of each of the line inputs. If
S01MUTEI*2Toggle mute status of all inputs. S01MUTEI*abcd , where each of the letters (a, b, etc.) is either 0 or 1 depending of the current status of
S01MUTEO*?Query mute status of all outputs. S01MUTEO*abcd , where each of the letters (a, b, etc.) is either 0 or 1 depending of the current status of
cancel 10 dB of noise. Higher numbers mean more cancellation will be applied, but may result in slight artifacts depending on the characteristics of t
This command controls the non-volatile memory lock feature. When NVLOCK is enabled, the user may not save any system settings to non-volatile memory.
S01NVPSWD?Query the current non-volatile memory password. S01NVPSWDlemur8.114. PEQIA -- Set All Parameters for Specified Parametric EQ Input StageThis
Parametric (1) Yes Yes Yes NoLow Shelf (2) No Yes Yes YesHigh Shelf (3) No Yes Yes YesLowpass (4) No Yes No NoHighpass (5) No Yes No NoLinkwitz-Riley
S01PEQIAB,1,?Query the current parameter settings for the parametric eq filter on input B , band 1. S01PEQIAB,1,t,f,b,g,s,e , where the parameters t,
the parametric equalizer (EQ) filters on input channels 1, A, B, and T . Each channel has five bands of parametric EQ that can be independently contro
Commentaires sur ces manuels